Monofeet^TM

On my own system I have a series of granite isolating platforms. These sit on MonoFeet^TM. The appliances sit on the granite slabs. Its a bit like this:
Table,
EPDM blocks of 100 x 100 millimeters,
( placed at the extreme corners of the Granite Slab ).
.
Granite slab
( 32 millimeters thick ),
.
MonoFeet^TM,
( only 3 Monofeet^TM are required placed in triangular configuration. One at the front in the middle and one each at the extreme ends at the back ).
.
Another granite slab
( also 32mm thick ),
.
Audio Appliance ( CD or Turntable ).
.
All audio appliances come equipped with isolation feet. Installing isolation devices directly onto the chassis of the audio appliance defeats the purpose of having the isolation feet and actually transfers sonic noise directly into the appliance.
By using a double isolation platform, the appliances isolation feet ( where the manufacturer has engineered the appliances sonic isolation platform ) the appliance works better and sounds better.
The best stone for isolation purposes is large crystal Pegmatite.
This may be difficult to acquire and so other granites are acceptable. Also acceptable is Slate and Marble.
A cheap alternative to rock and equally effective is the common garden concrete paver slab. These are available from most plant nurseries and hardware stores and are generally 600mm x 600mm by 25mm - 50mm thick. They can be painted and are more easily adaptable to existing decor.
As well as being used to isolate audio appliances the Kit can be placed as an interface between your speakers ( or speaker stand ) and the floor on high density EPDM blocks. By isolating the speaker from the floor with MonoFeet^TM  adds further to stabilizing  the stereo holographic field.
All Tweaking helps!
Contact your local stonemason for your granite slabs. If you have any problems contact Bocchino Audio and I can forward you the appropriate Bocchino Audio Isolation Platform Kit sized for your appliance.
Granite slabs supplied with the Kit are 18mm thick, other thicknesses are available. The slabs with the kit have only the top face polished and are fully arrassed to remove sharp edges.
Colour is speckled black and white. You must specify the maximum exterior footprint dimensions of width and depth and mass of your appliance either in Imperial or Metric measurements when ordering this kit.

Monopole® Connector Brackets.

              Designed exclusively for use to connect  Monopole® on the amplifier with Monopole® on the speaker  this cable is made from pure Copper strip ( 99.9%+ pure Copper )  0.7mm wide x 32mm high with a DC  resistance of less than 600 Micro-Ohms per meter.   Two strips make up each cable and these are separated by being located into a low density foam block with a minimum separation distance of 30mm. Each strip is electroplated firstly with anodic copper ( >7N ) followed by pure silver  for the entire surface area of the metal strip.
This completely eliminates the possibility of the formation of Copper Oxide on the surface of the metal.
The strips are then wrapped initially in low density fiber and then wrapped in a very low permeability insulator. This assembly is further wrapped in low density fibber , low permeability insulator and then shielded from RF. With a further insulative wrapping before the final jacket is socketed over the cable assembly.   The cable has the Bocchino Audio FM3 Spade profile integral at both ends for easy connection to your Monopoles®.

 B.A.S.S. Straight^TM cable is 71 x 71 millimeters in cross-sectional dimension.

 B.A.S.S. Straight^TM    is delivered inserted into a plastic pipe so as to maintain its straight shape. The 'fly-ends' are 350mm long and are flexible enough to be inserted into the Monopole®  interface.

 B.A.S.S. Straight^TM will bend but over a longer radius than normal audio cable. Not as flexible as coiled speaker wire but what a difference it makes! Nominal bending radius is 600mm or 2 feet.
 B.A.S.S. Straight^TM is available in 2.5 meter and 5 meter lengths.  Other lengths are available on special order.
Also available in Fine Silver ( 4N: 99.99% pure Silver) and Fine Gold ( 99.99% Pure Gold )
B.A.S.S. Straight^TMSilver is not plated. Its appearance is its natural metal colour: Silver.

MonoMass^TM